Non-Export Solar Systems in California: What They Are and When They Make Sense

In short: A non-export (or “zero-export”) solar system is set up so it never sends power to the grid. In California this is an approved interconnection type under Rule 21, and it still has to be permitted and approved by your utility. Because you receive no export credits, it only makes sense when you can use almost everything you produce, usually with a battery. Its best-known use is adding capacity to an older NEM 2.0 system without losing that status, and installers use it to keep new solar from counting as export under the Net Billing Tariff. Rules and fees vary, so confirm the details with your utility in writing.

Time-sensitive. Last verified: 8 October 2026. Rule 21, utility procedures and fees can change, and much of what’s published online comes from installers. Treat this as a guide to what to ask, not as a ruling on your case. See the checklist at the end.

Search interest in “non-export solar California” has grown as export credits fell under NEM 3.0. This guide explains what these systems are, how they’re controlled, what you give up, and when they make sense. For the bigger picture, read NEM 2.0 vs NEM 3.0: Key Differences first.

What is a non-export solar system?

It is a solar system (usually with a battery) whose output is controlled so that power flows only to your home and your battery, not back to the grid. You’re still connected to the utility for power you buy, but you don’t sell anything.

Standard grid-tied (Net Billing Tariff) Export-limited Non-export (zero export)
Sends power to the grid Yes, up to your system’s output Yes, only up to an approved limit No
Export credits Yes, at avoided-cost values Depends on the program None
Needs export-control equipment No Yes Yes
Needs utility approval Yes Yes Yes

How does it work?

  1. The panels produce power, which first serves your home.
  2. Any surplus charges your battery.
  3. When the battery is full and the house is using less than the panels make, the system reduces its output (curtails) instead of exporting.

The export limit is enforced by equipment: smart inverters and gateway controllers with export-limiting settings, or a certified Power Control System (PCS), a device that Rule 21 recognizes for keeping a system from exporting. Which setup is accepted depends on your utility and project.

Is non-export solar legal?

Yes. Rule 21, California’s interconnection rule, includes non-export systems, and the CPUC has treated them as a distinct category. But “non-export” doesn’t mean “no paperwork.” The system must still be permitted, inspected and approved by your utility. Installing unapproved solar that is “set not to export” can cause problems with your utility and insurance, so make sure your installer files the application.

What you give up

  • Export credits. Whatever you can’t use or store is lost. Under the Net Billing Tariff those credits are small (see California NEM 3.0 Explained), but under NEM 2.0 they can be valuable.
  • Some of your production. The system curtails when your battery is full and you’re not using much.
  • Time. A policy filing to the CPUC notes that interconnection timelines for non-export systems can be slow, so ask your installer for a realistic schedule.

When non-export can make sense

1. Adding capacity to an older NEM 2.0 system

NEM 2.0 customers can expand their solar by the greater of 1 kW or 10% and keep their status (see Does Adding a Battery Affect Your NEM 2.0 Status in California?). Installers report that PG&E, SCE and SDG&E also have approved methods to add more capacity as a non-export addition under Rule 21, in a way that doesn’t affect NEM status. Because this is exactly the kind of detail that differs by utility, ask yours for the rule in writing before you build.

2. Homes that can use almost all their solar power

High daytime use, an EV charging at home, a pool pump or a large battery can absorb most of what the panels produce. In that case, giving up exports costs little.

3. Homes where backup matters more than export income

If your main goal is power during outages, a solar-plus-battery system that keeps your home running may be more valuable than export credits. See Solar Batteries and Blackouts.

When it usually doesn’t make sense

  • No battery and low daytime use: you’d waste much of the production.
  • Exports are valuable to you, for example because you’re on NEM 2.0 and can expand within the allowance.
  • You don’t want to rely on a control device that must work correctly to stay compliant.
  • Your usage is small, so a battery and controls cost more than they save.

From the field: working on systems that don’t export

I should say up front that my experience with this type of system comes from Spain, not California, and the rules and paperwork are different. But the way these systems work in practice is similar, so a few things I learned carry over.

How the export limit was set up

On the non-export systems I worked on, we limited what went to the grid with a meter that measured the home’s consumption, plus settings in the inverter that reduced the output when the house wasn’t using everything the panels produced. That’s the basic idea behind any zero-export design: something has to measure, and the inverter has to react to it. For the full technical explanation, read How Zero-Export Solar Works.

Where the difficulty was: the paperwork

The hardest part of these jobs was usually the paperwork, not the equipment. Even when a system isn’t meant to send power to the grid, you still have to follow the approval process, so allow time for it and ask your installer exactly which steps they’ll handle. In California that means following your utility’s interconnection rules, as described above.

Who it suited

I’d recommend this kind of system mainly to households that do most of their demanding activities during the day, because those homes can use most of their solar power as it’s produced and give up little by not exporting. If your biggest uses of electricity come in the evening, the case is weaker, which is where a battery or a different design may help.

A simple way to compare

Illustrative example only. Suppose you add solar that would produce 3,000 kWh a year beyond what you and your battery can use.

  • Under the Net Billing Tariff, exporting it at about $0.07 per kWh would earn about $210 a year.
  • As non-export, you’d earn $0 on that part, but you’d avoid a 9-year export rate lock, extra fees or leaving NEM 2.0, if you were on it.

Whether that trade is worth it depends on your tariff, usage and the added cost of the controls. Ask installers to model both options with your actual rate plan. Learn how to run the numbers in How to Calculate Your Solar Payback Period.

Checklist before you choose a non-export design

  1. Confirm which program you’re on (NEM 1.0, NEM 2.0 or the Net Billing Tariff) and your utility.
  2. Ask your utility, in writing, whether your non-export addition would affect your tariff and which interconnection steps apply.
  3. Ask your installer how the export limit is enforced (which device, which setting) and whether it’s a certified Power Control System.
  4. Make sure the project is filed as a non-export interconnection and that you get permission to operate before turning it on.
  5. Ask for the fees and the timeline, because they differ from standard projects.
  6. Get a design with the battery sized for your evening use. See Do You Need a Solar Battery? and Tesla Powerwall vs Enphase IQ vs Franklin.
  7. Compare quotes and check the installer’s licence. See How to Compare Solar Quotes and Spot Red Flags.

Common mistakes

  • Assuming “non-export” means you don’t need to tell the utility.
  • Installing a non-export system without a battery and wasting production.
  • Expecting the system to protect your NEM 2.0 status without checking in writing.
  • Choosing the design only for the NEM 2.0 loophole, without modeling the economics.
  • Believing an installer’s “100% self-consumption” promise without seeing your usage data.
  • Ignoring the added cost and complexity of the control equipment.

Next steps

  1. Identify your program and utility, and get 12 months of usage data, especially evening use.
  2. Decide whether you want export income, backup power or both.
  3. Ask for quotes with and without non-export, modeled on your rate plan.
  4. Read the wider California picture: Solar Panels in California: Complete Guide After NEM 3.0.

Frequently asked questions

What is a non-export solar system in California?

It’s a solar system configured so it doesn’t send power to the grid, usually with a battery. It’s an approved interconnection type under Rule 21 and still needs utility approval.

Do I have to tell my utility about a non-export system?

Yes. The system must be permitted and interconnected, and your installer files the application. “Non-export” describes how it operates, not whether it needs approval.

Do non-export systems get export credits?

No. Because they don’t send power to the grid, you receive no export credits, so the design makes sense mainly when you can use or store almost all of the production.

Can non-export solar protect my NEM 2.0 status?

Installers report that utilities have approved ways to add non-export capacity to a NEM system without changing its status. Because details differ by utility, confirm in writing with yours before you build.

Is a battery required for non-export solar?

Not required, but without storage you’d waste any production you can’t use immediately, so most designs include a battery.

Is non-export solar worth it?

It depends on your usage, your tariff and the cost of the controls. It can make sense for homes that use most of their solar power or want backup, and for NEM 2.0 owners who want more capacity. For others, a standard system with a battery may be better.

Scroll to Top