Solar Panels on Flat, Metal, Tile and Slate Roofs

Most solar guides assume an asphalt shingle roof and stop there. In real life, plenty of homes have a standing seam metal roof, clay or concrete tiles, slate, or a flat roof, and the answer to “can I put solar on it?” is almost always yes. What changes is how the panels are attached, who should do the work and what can go wrong. This guide walks through solar panels on different roof types so you know what to ask before you sign a quote.

Whatever your roof is made of, two things come first: its condition and its direction. If the roof is near the end of its life, fix that before the panels go on. And if you haven’t yet, check which direction and angle suit your roof.

Solar panels on different roof types at a glance

Roof type How panels are usually attached Main thing to watch
Asphalt shingle Brackets screwed into the rafters, sealed with flashing The easiest case. Check roof age.
Standing seam metal Clamps that grip the raised seams Using mounts made for your seam type
Corrugated or screw-down metal Screws through the roof, with sealant Leaks at every fixing point
Clay or concrete tile Special hooks under the tile, or replacement tiles Broken tiles and watertight flashing
Slate Brackets on the rafters, with tiles lifted and cut around them Slate is brittle, so you need an installer who has done it
Flat roof Ballasted frames (weighted) or frames bolted to the deck Roof load, wind and the membrane warranty

Solar panels on a metal roof

Metal roofs are a very good match for solar, as long as the mounts suit the type of metal. There are two main families:

  • Standing seam. The raised seams between panels let installers clamp the mounting hardware on without drilling through the roof. That’s the big attraction. The one rule is not to bend or alter the seams, so the clamps must fit your specific seam profile.
  • Exposed-fastener (screw-down) and corrugated. These need screws through the metal, so every fixing point is a place a leak could start. Installers should use corrosion-resistant, UL-listed sealant on each penetration. Some roofs have foam insulation underneath that needs a spacer, and some don’t have the strength or space for standard flashing.

Before you agree to anything, ask whether the work could affect your roof warranty. Manipulating the roofing material can void it, so get the roofer or the manufacturer’s position in writing.

Solar panels on a tile roof

Clay and concrete tile roofs can take solar, but this is where the installer matters most. Tiles are fragile, especially if somebody walks on them the wrong way, and they sit on top of a waterproof layer that has to stay waterproof afterwards.

  • How it’s done. Installers either use mounts with a base that slides under the tile and fixes to the roof structure, or they lift a few tiles, attach brackets and modify or replace the tiles around them.
  • The risks. Cracked tiles during installation and leaks if the flashing isn’t done properly. A good crew uses walk pads and handles tiles carefully.
  • Ask: who will be on the roof, whether they’ve done tile roofs before, what happens to broken tiles (the installer should replace them), and whether you can get spare tiles ahead of time. Old tiles can be hard to match.

You should expect the work to be more involved than on shingles, and the quote to reflect that. Compare at least three quotes. Our guide How to Compare Solar Quotes and Spot Red Flags shows what to look for.

Solar panels on a slate roof

Slate is the most delicate of the common roof types, and it’s usually the most expensive to work on. It’s more common in the UK and in older parts of the US Northeast.

  • Never drilled. Drilling through slate can damage the tile and cause leaks later. Instead, the installer lifts the slates, fixes the brackets to the rafters, adds flashing and cuts the slates to fit around the bracket before putting them back.
  • Brittle. One installer quoted in a UK guide says that if you “just lift up a slate tile and try to wriggle it out, it’ll snap”. A competent installer replaces any slates broken on the job.
  • Slower and costlier. Expect the installation to cost a bit extra and take a day or two longer than a standard job.
  • Planning, in the UK. Slate roof solar usually falls under permitted development rights, but flats, listed buildings and homes in conservation areas often need extra permission.

For UK costs in general, see Solar Panel Cost in the UK.

Solar panels on a flat roof

Flat roofs give you freedom, because the panels sit on frames and you choose the direction and angle. The trade-off is the frames themselves, the weight and the wind.

  • Ballasted systems use weight (blocks or trays) instead of fixings, so they usually leave the roof membrane alone and are more likely to preserve its warranty. They add load to the roof, so someone needs to check the structure can take it.
  • Attached systems are bolted to the roof deck. They weigh less but make holes, so you need to coordinate with whoever maintains the roof membrane.
  • Tilt. Low tilts of around 10–15 degrees are common on flat roofs, because steeper frames catch more wind and need more space between rows to avoid shading each other.
  • Wind. Edges and corners see much stronger uplift than the middle of the roof, so good designs put extra weight or anchors there.

More on tilt and row spacing is in our roof direction and angle guide.

From the field: what I saw installing on tile and metal roofs

I’ve installed solar on both tile and metal roofs, and tile was the easier of the two for me. The catch is that tiles break. If you’re not careful about where you step and how you handle them, you end up replacing a lot of them, so slow, careful work matters more than speed.

Metal was harder, and the hard part was fixing the mounts. Getting a solid, secure fixing for the supports on a metal roof takes more thought than on a tile roof, and this is the step where a rushed job shows up later.

The mistakes I saw most often were these:

  • Not orienting the panels well. It sounds basic, but it costs production for the life of the system.
  • Using a mounting structure that isn’t strong or certified enough. The panels are only as secure as what holds them to the roof.
  • Wiring the connections badly. Poor cable connections are a problem during installation and a risk afterwards.

Before you hire anyone, my advice is to start with your real consumption. Look at what you actually use and size the system to that, so you don’t pay for more than you need. I’d also consider a home battery, since it lets you keep part of the electricity you generate. That’s my view from the field and it won’t suit every home, so see Do You Need a Solar Battery? to check the numbers for your case.

Check these before you choose, on any roof

  1. Roof age and condition. Many installers recommend replacing a roof that’s close to the end of its life before installing panels, because taking panels off and refitting them later adds cost.
  2. Roof warranty. Ask your roofer or the manufacturer how solar mounting affects it, and ask your installer to put its own workmanship guarantee on leaks in writing.
  3. Structure. A structural check is standard before installation, particularly for heavy tile or ballasted flat roofs.
  4. Installer experience. Ask how many roofs of your type they’ve done this year. Our installer checklist has the questions.
  5. The exact mounts. The quote should name the mounting system and say how it attaches to your roof.
  6. Insurance. Tell your home insurer about the system and confirm it’s covered.

Does the roof type change the cost?

It can. Shingles are the simplest case, standing seam metal is usually straightforward, and tile, slate and some flat roofs involve more labour and specialist parts, so the quote tends to be higher. The size of the difference depends on the installer and your area, so rely on itemized quotes rather than a rule of thumb. For typical prices, read How Much Do Solar Panels Cost in 2026?, and use the Solar Savings Calculator to see how a higher price changes your payback.

Frequently asked questions

Can you put solar panels on any type of roof?

Almost any, but not every roof is a good candidate. A roof in poor condition, one that’s heavily shaded or one facing the wrong way may not be worth it. A roof inspection and an installer visit will tell you.

Do solar panels damage a metal roof?

Not if the right mounts are used. Clamps on standing seam roofs don’t need holes, while screw-down roofs need sealed fixings. Ask about the effect on your roof warranty before you sign.

Can solar panels go on a tile roof without breaking the tiles?

Yes, with an experienced crew using proper walk protection and tile-specific mounts. Some tile breakage can happen, so ask who pays for replacements and whether spares are available.

Is it harder to install solar on a slate roof?

Yes. Slate is brittle, so installers lift and cut tiles rather than drill. That typically makes it slower and a bit more expensive than a standard job.

Are flat roofs good for solar panels?

They can be. You choose the direction and tilt, but you’ll need mounting frames, a check on roof strength and a plan for wind. Ballasted systems usually protect the roof membrane better.

Sources

This guide is general information, not engineering or roofing advice. Have a qualified installer and, where needed, a roofer or structural engineer check your roof before work starts.

Scroll to Top